ALIGN 3GX 2.1 MANUAL PDF

The manual is embedded in the build instructions for the various Align kits. This appears to come out of the manual. At least its identical to. i have just ordered an Align 3gx flybarless control unit but i can’t find any instructions online anywhere as i like to usually download and print. Align 3Gx flybarless setup problem Electric Heli Talk. Registered User Without the 3Gx module in place, with servos connected directly to.

Author: Vorisar Vudonris
Country: Suriname
Language: English (Spanish)
Genre: Software
Published (Last): 6 December 2017
Pages: 166
PDF File Size: 11.49 Mb
ePub File Size: 12.92 Mb
ISBN: 749-7-15496-336-6
Downloads: 52698
Price: Free* [*Free Regsitration Required]
Uploader: Vudokree

Been there,, done that!

The caution at or near the bottom of the page tell you that you may to re-map the channels 3 to PIT instead of to THRO and therefore the manual alkgn not incorrect. Well done eban I didn’t spot the mistake and the problem nearly brought my very short experiment with FBL to an untimely end.

Confirm the 33gx settings by pushing the SET mmanual. With all channels stationary, move the transmitter aileron stick to the right and then back to center position.

Check that there is no binding throughout the pitch range. Jul 06, It’s a must and to be mmanual with the dongle via usb port on the PC. If not this will effect the travel of the servos Originally Posted by 3ddd i just found out the manual for mine was printed wrong,if you are using futaba it shows zlign yellow wire going to channel 3 and the purple wire going to 6,they are backwards and need to be switched,but i think this only applies to standard futaba channel mapping.

Settings export feature allows custom settings to be shared amongst friends. Jul 25, This appears to come out of the manual. Also you cant update the firmware with your transmitter lol. It just the way Align assigned channels in the 3GX unit versus the way Futaba assigned channels in its rx and S-bus. This can only be done through actual flight tests.

  BU2508AF DATASHEET PDF

That’s a bit awkward for, if I read the CD correctly, I have to do that with the 3Gx installed in the heli, which means bringing the whole thing to my Qlign because I don’t have a laptop like they show in the CD. This completes the rudder endpoint limit adjustment for the right side.

3GX manual – HeliFreak

Jul 15, My HK 3GX setup. Align 3Gx flybarless setup problem. Therefore, BEC output capability should be confirmed to handle burst current when setting collective pitch acceleration, otherwise insufficient current supply may result in flight accidents.

He was getting a bit defensive, suggesting I had some kind of mix in my transmitter, but I kept reminding him it behaved normally when connected direct to my receiver. Others have confirmed to me that they’ve set up their 3Gx without using a PC, so I think mine must be alin. Options Quote message in reply? For radio with built in gyro gain settings, gain can be adjusted directly. This is how to do the setup through the 3GX unit. This setup mode sets the elevator 21 direction. Sign manaul now to remove ads between posts.

Align 3Gx flybarless setup problem – RC Groups

Support with APS gyro system and bring up more functions for your helicopter. Anyway, I’ll hook aligj up to my PC tomorrow and, hopefully, the setup program will either fix the anomoly I’m seeing, or confirm that it’s a fault. You need to pick servo type before even connecting the servos or you have the potential to damage them.

  LEOPOLDO MARIA PANERO POESIA COMPLETA PDF

Release the button before the flash sequence complete, the DIR green LED will light up indicating the 3GX has been bypassed for mechanical neutral and travel range setup. After I swapped the yellow and purple wires, the servos behaved as they should. Anything else I should try, please, before telling the vendor that the unit’s bad?

Pirouetting flips type of maneuvers are easily accomplished with precision. If the helicopter hovering tend one side, it means the swashplate doesn’t keep horizontal manial setting.

The recommended collective pitch range for various T-Rex helicopters 21. degress depending on preferenses. Confirm the transmitter is powered up, and throttle stick is at lowest position. In order to be able to post messages on the HeliFreak forums, you must first register. The dramatically improved performance will create immediate impact on any enthusiasts. The manual is embedded in the build instructions for the various Align kits.

Posting Quick Reply – Please Wait. Setup mode will exit if no activity is detected in 10 seconds.

Align 3gx pdf manual

I realise I’m going to probably have to modify the throttle curves and pitch curves later for thebut at least it’s a starting point. To get purple to channel 3 and yellow to channel 6 I have to cross the wires over and they’re out of sequence in the normal electronics colour coding convention.

This completes the aileron endpoint setup process.