Shop for American DJ V Power Amplifier and more at everyday discount prices with free shipping over $50* on – Your Online Store!. Buy the ADJ V Amplifier at PlanetDJ. Low VIP Pricing, Financing and Free Shipping available. American Audio | V | User manual | American Audio V User manual American Audio┬« – – V Vplus Series Amplifiers Power.

Author: Shakataur Ditaur
Country: Qatar
Language: English (Spanish)
Genre: Life
Published (Last): 23 February 2018
Pages: 114
PDF File Size: 3.24 Mb
ePub File Size: 7.51 Mb
ISBN: 381-6-57587-612-2
Downloads: 58573
Price: Free* [*Free Regsitration Required]
Uploader: Kazrashicage

Fuse Holder – 10 5 11 6 12 1 Diagram 3 This holder houses the external fuse.

The amplifier can operate at practically any power level without risk of overheating. Cooling Vents – These vents are used for proper cooling.

Never aemrican your amplifier in to a wall outlet that does not match the required voltage of your amplifier, serious damage may occur to your unit. Fuse Holder – This holder houses the external fuse. Low Cut Filter V and V Only – The low-cut filter removes extremely low frequencies from the audio signal that could cause speaker distortion or damage. Check the line from the output terminal of the amplifier to the speaker.

Before using this amplifier, read the user manual for further warnings. It’s a community-based project which helps to repair anything.

American Audio V User manual |

Ground Lift Switch – This switch is used to disconnect the internal ground signal from the amplifier chassis ground.


If the input gain level is not reduced the built-in limiter will activate. No user serviceable parts inside. Turn channel two gain up. This booklet contains important information concerning the proper and safe operation of your new amplifier. When constructing your own XLR cables follow the pin configuration describe below for proper connections.

Insert the spade connector in to the binding post and tighten the caps down on the spade connector. When the channel goes into protect mode all output for that channel will turn off. Cooling Fan Dual speed cooling fans. If it is lit about half the time, the amplifier channel will probably go into thermal protection within a few minutes.

This light may continue to glow briefly after main power has been turned off, this is normal. If this line good, check the internal speaker connections and components.

American Audio V3000/V2000 Stereo Amplifier User Manual

The front panel provides four holes used to screw the unit into a rack. An ultrasonic network uncouples RF from the output and helps keep the amplifier stable with reactive loads.

Connecting to the wrong voltage is dangerous and may damage the amplifier. A short aemrican will usually be traced to a bad cable or a bad speaker component and is rarely traced to the amplifier itself.

Banana Plugs – When connecting your speakers to the amplifier using banana jacks; Be sure that the red and black caps amerlcan the binding post are completely screwed in. See page 9 for more details on input configuration.

  LEY 26366 PERU PDF

Connect an input signal to channel one. Be sure that supplied voltage matches that of the required voltage of you amplifier.

American DJ V3000 2 Channel Professional Stereo Amplifier

Use your front gain controls to regulate the output volume. Always use the 50 Hz filter setting if you are using the amplifier to drive a distributed line system also known as a constant-voltage line, 70 volt line, amerrican. Mono bridge operation connections will follow the above descriptions however, when operating in mono bridge operation the speaker connections will run between the two positive red leads. The speaker wire may be connect by bare wire directly connected, usually for permanent connectionsbanana plug, or spade connector.

When connecting your speakers to the amplifier using banana jacks; Be sure that the red and black caps on the binding post are tighten down completely. When dip switches 2 and 3 are in the “ON” the filter will cut off frequencies at and below 30Hz, when these dip switches are in the “OFF” position the filter will cut off frequencies at and below 50Hz. Sj will allow brief clipping of peaks and will only activate when continuous, hard clipping occurs.