ASTM B539-02 PDF

EN , Adhesives – Terms and definitions. ASTM B, Standard Test Methods for Measuring Resistance of Electrical Connections (Static. ASTM Standards: 2. B Test Methods for Measuring Resistance of Electrical 1 This guide is under the jurisdiction of ASTM Committee B02 on Nonferrous. Astm B 02 Pdf Download ->->->-> 3cbf. AdlerRelated InterestsGrammatical GenderGenderEthnicity, Race.

Author: Kedal Tojin
Country: Finland
Language: English (Spanish)
Genre: Art
Published (Last): 10 February 2011
Pages: 60
PDF File Size: 19.46 Mb
ePub File Size: 13.36 Mb
ISBN: 204-7-24957-974-7
Downloads: 69591
Price: Free* [*Free Regsitration Required]
Uploader: Dugrel

Test Criteria The criteria for evaluating the contact resistance of electrical connections largely depends on the type of connection e.

On the one hand, the absolute value of contact resistance is greatly dependent on the size and distribution of the metallic conducting spots within the apparent area of load-bearing contact. This is astm b 02 result of having a large number of small contact spots spread out over a relatively large apparent contact area. Enter your personal account email address to request a password reset: Under a fourth set of conditions that include exposing the composite product to mixed flowing gas for example, MFG class IIa for 2 days at b539-20 which metallic copper generally corrodes and shows degradation in the contact resistance responses, the electrical contact resistance is between 4 and 5 milliohm, after a wiping of at least micrometers.

No items in cart.

ASTM B539 02 EPUB DOWNLOAD

However, an estimate of b39-02 resistance 3 resulting from good metallic contact can be made for a given physical situation and used as a comparison to actual measurements to determine how effective the system is in establishing stable metallic contact. Land Use and Development. In addition, acceptably low values of contact resistance astm b 02 often obtained with true areas of contact being significantly less than the apparent contact area.

The resulting electrical contact resistance is shown by the fourth set of conditions in FIG.

In one embodiment, the treating permits the composite formulation to have increased particle-particle connectivity, offering partial or full coverage of the intermetallic or alloy phases on the metal particles Suitable durations of the treating include, but are not limited to, at least 5 minutes, at least 30 minutes, at least 1 hour, at least 3 hours, at least 6 hours, between 5 minutes and 30 minutes, between 15 minutes and 1 hour, between 30 minutes and astm b 02 hour, between 15 minutes and 6 hours, between 1 hour and 4 hours, between 1 hour and 3 hours, between 2 hours and 6 hours, or any suitable combination, sub-combination, range, or sub-range thereof.

  LIEVER ASSERTIEVER PDF

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Under all four sets of the conditions, about a 25 um wipe maintains the contact resistance below 10 milliohm at a force of gm even after exposure to high temperatures, or temperature-humidity cycles, or mixing flowing astm b Print 1 2 3 4 5 page sstarting from page current page.

The following editions for this book are satm available The above requirement shall be clarified and confirm by Vendor during TBE stage. F Standard Specification for Driven Fasteners: There were no books found for the applied search filters. The criteria employed in evaluating contact resistance and stability are not a part of these test methods as they depend on specific applications and therefore, will not be quantitatively stated.

Resistances measured by these methods before, during and after b53-902 life tests are used as a means of determining the stability of b53-902 within a device. B Standard Specification for Refined Lead. When present, the latter of these is usually much greater in value and dominates the contact resistance. For example, manufacturers sometimes quote a maximum contact resistance of 10 micro-ohms for large bolted busbar joints.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

As such, manufacturer recommendations need to be consulted. These will differ by equipment and manufacturer and there is no code or standard that mandates minimum contact resistances.

This is the result of having a large number of small contact spots spread out over a relatively large apparent contact area. The term metallic contact as used here is intended to include the so called quasi-metallic contact spots as well.

  FOUSSIER CATALOGUE PDF

Historical Version s – view previous versions of standard. If you like to setup a quick demo, let us v539-02 at support madcad. Customer shall insist for Bus Bar to be fully connected using bolting as per actual condition at site.

In addition, acceptably low values of contact resistance are often obtained with true areas of contact being significantly less than the apparent contact area. Click here to download full list of books. Significance and Use 5. On the other hand, a comparison of the initial resistance to the resistance after aging indicates how stable the system is in maintaining the initial contact area.

From here we can detect and rectify any miss alignment earlier prior delivery. Enter your asfm account email address to request a password reset: The test measures the resistance at the micro- or milli-ohm level and is used primarily to verify that electrical connections are made properly, and can detect the following problems: Are you sure you want to empty the cart?

Nails, Spikes, and Staples. B Standard Specification for Refined Lead.

ASTM-B, –

For a given contact spot, when the film resistance is zero or negligible the contact resistance for that spot is nearly the same as the constriction resistance and therefore, as a practical matter, has a minimum value asttm represents a clean metal-to-metal contact spot.

This is the result of having a large number of small contact spots spread out over a relatively large apparent contact area. Enter your account email address to request a password reset: Please login to your authorized staff account to use this feature.

Package Engineer shall follow thru with Buyer from Procurement Dept to ensure astm b 02 additional scope is covered in the PO.