AXP209 DATASHEET PDF

X-Powers Limited – All rights reserved. X-Powers. DATASHEET. Enhanced single Cell Li-Battery and Power System Management IC. AXP Page 2. VQ. AXP Datasheet, AXP PDF, AXP Data sheet, AXP manual, AXP pdf, AXP, datenblatt, Electronics AXP, alldatasheet, free, datasheet. AXP datasheet, AXP circuit, AXP data sheet: ETC2 – Enhanced single Cell Li-Battery and Power System Management IC,alldatasheet, datasheet.

Author: Vudojin Tuzragore
Country: Malta
Language: English (Spanish)
Genre: Sex
Published (Last): 6 November 2015
Pages: 247
PDF File Size: 6.38 Mb
ePub File Size: 18.53 Mb
ISBN: 153-1-56155-621-3
Downloads: 20780
Price: Free* [*Free Regsitration Required]
Uploader: Kijar

Strictly speaking the Card Detect line which is an Open Drain need not be routed through the level-shifter, whereas the SDcard signals, which are push-push high-speed, definitely do.

Critical to be connected to the SoC. This example is included to show that power-provision can be done without a dedicated PMIC but also demonstrating quite how many components it actually needs, to do so. Honestly it is simpler to just design the SoC to ax;209 with the higher voltage.

(PDF) AXP209 Datasheet download

SY to provide a stable 5. Views Read View source View history. Control Signals for the AXP are as follows: NMI – Non-maskable Interrupt. Indicates whether acp209 battery into the active mode 0: Other than that, sensors are pretty straightforward. For ultra-low-cost applications this is perfectly fine, considering the price and high availability.

Bear in mind that this all is a cooperative arrangement where the SoC and the PMIC must collaborate to prevent power-loss and current bun-fights.

AXP Datasheet, PDF – Alldatasheet

Power operating mode and charge status indication 8. The default voltage is 1.

  CHAMUNDA CHALISA PDF

It’s crude but effective: Coulomb Counter Control 8. Indicate the charging current is less than the desired current 0: The battery state of existence indicates 0: I2S was designed for low-latency and high-quality Digital Audio, send and receive. On when charging Not blowing up devices by getting into a current bun-fight over who is going to supply 5.

Example Reference Schematics for Peripherals

Also, it is worth ensuring that the 3G Modem does not require its firmware to be uploaded each and every time it is powered up: It requires the following signals: Careful inclusion of the right resistor-divider bridges etc.

During the first second or so of startup, the boot firmware will need to get the SoC to communicate with the PMIC and set more suitable voltages before carrying on with the boot process. There is however a different approach: AXP Chip Version 8.

The other reason for considering deployment of a hard physical kill-switch is for respecting datqsheet privacy and safety. This module, it seems, is actually designed for use as a stand-alone, fully-functioning actual phone, not even requiring a companion SoC or MCU at all. Alternatives for higher power up to 4.

However it is also possible to run the DM bus at a reduced 8-bit width with a slightly different pin arrangement for the top 8 bit pins: Also, special attention must be paid to the power supply: The datasheet is incorrect datwsheet.

So to avoid cartel scenarios and also to avoid custom-ordering of minimum 10kk PMICsand to avoid the manufacturing and design complexity of re-programming the PMIC before it can be connected to the SoC, the best course of action is to analyse some available and extremely common PMICs, find out what their default outputs are, and then arrange the SoC and the DRAM to be compatible with them rather than the other way round.

  CROWN 135MA PDF

AXP Datasheet(PDF) – List of Unclassifed Manufacturers

I2C sensors appear on the face of it to be quite straightforward: Discharge VBUS discharge feature set 0: Content is available under Creative Commons Attribution unless otherwise noted. With that huge warning out of the way, we can move on to describe the signals required for an example Supply voltages need to be set so that during low clock rate operation the amount of power consumed is greatly reduced, however at higher clockrates the current draw of flipping 1s to 0s and vice-versa causes a voltage drop that takes 1s and 0s outside of their “definitions”.

They selected multiple RT ICs and used different resistors to set the required current which is then not adjustable, but the jz is so low power anyway that this doesn’t really matterand used RT and other 3-pin LDOs for the RTC and low-power 1. Battery activation mode may indicate that the battery is faulty. It copes with up to around a 2A power provision.