GENERAL. Usage of Maintenance Manual. FR-SF series inverters are designed to drive machine tool spindles, and feature quiet operation, stable and rapid. Hi all: Could anyone please explain the difference between the FREQROL FR- SE and FR-SF??? To me they sound the same I thank you for. Repair service for FR-SFK-CE Mitsubishi AC Spindle Drive 26kW VAC FREQROL FR-SF Condition: Send-in repair. Free evaluation. 6 Months warranty .

Author: Tojagrel Zujora
Country: South Africa
Language: English (Spanish)
Genre: Technology
Published (Last): 5 August 2007
Pages: 82
PDF File Size: 18.72 Mb
ePub File Size: 17.2 Mb
ISBN: 784-1-27679-418-1
Downloads: 49845
Price: Free* [*Free Regsitration Required]
Uploader: Nagor

See each listing for international shipping options and costs. Enter the email address you signed up with and we’ll email you a reset link. Powered up and all LED’s working. An instantaneous power 0 Check the voltage waveforms 0 Check the cause of the failure which lasts for at the amplifier input termi- instantaneous power failure 15 msec or more occurs nals Xl, X2, and X3 using an and take porper counter- the input votlage drop2 oscilloscope.

At the time, take care not to collide the sensor with the detection gear. See the following figure. We will do our best to resolve the issue. So the top Therminal strip is pulling the drive down. Inverter side See Appendix 9 l.


The speed reference signal input type is selected. When the orientation time is long because the time period point b to c on which the spindle rotates at a creep speed, increase OSP and PGl in the man- ner that the spindle doesn’t overrun when it stops.


I’m pretty sure the problem is where s SF-CA card plugs onto the power supply. The orientation encoder o In the same manner as the o Replace the encoder with the of the spindle is defec- Item 1 of the alarm No. There was a problem completing your request.

You have the option to buy a product that is much cheaper than a Brand new version of the product and save money while benefiting from a quality product refurbishment process according to strict procedures prior to being offered for sale, fully tested and vr by skilled technicians in order to ensure quality of our repair and refurbishment process.

Does it vary remarkably depending on the time zone?

At the time, correct the fgeqrol using the parameter ORS2 bit 8. Remove the P flat head screw which fastens the cooling fan from the inside of the fan case and the cool fan can be dismounted from the fan case. However, to return back to 2 the normal operation mode, make sure to set the CVHS to “0”.

GRB4 5 is weak. The cooling fan is dirty 0 visually or by touching the o Clean the cooling fan using 6 by dust and the cooling cooling fan, check the a factory utility air or effect is degraded. Ground a cable which connects the motor ground and controller ground.

When “1” is set to Y45wT bit 8, this parameter is valid. Frsqrol no position loop is formed, the position droop is 0. See Appendix 6 l.

Mitsubishi AC Spindle Drive FREQROL-SF Maintenance Manual

Your very well clued in on everything Mazak. Find and Buy online the model required on your Machine-Tools. Same as encoder previous 1: The cable between the o In the same manner as the o Replace the cable with a new spindle orientation en- Item 3 above, check the wave- one.


PIN2 should be set at the same When the equipment is linked to the time. The following figure exemplifies a waveform of phase A.

Mitsubishi FR-SF spindle drive manual | ZEYNEL ULUSOY –

At the time the motor speed remains as the orienta- tion speed. El – 00 Fig. It seems I found a typo or two in the charts that caused me great confusion. Motion A – The base shut-off occurs in the controller, the main circuit COntaCtor is turned off, and the motor stops in the free-run state.

The Ki magnification should be set to the magnification for 37 VKI. In stock 5 days – Usually ships in business days. Amazon Restaurants Food delivery from local restaurants.

I insulated the cables that connect to the spindle drive as I did before so I could turn on the power to keep the batteries charged and it’s an old screen so I like to power it on for an hour a day. Got rid of the problem with the bad connection of the SF-CA card to the power supply and it’s perfect.