IEC 60268 7 PDF

IEC SOUND SYSTEM EQUIPMENT –- PART 7: HEADPHONES AND EARPHONES. Buy IEC SOUND SYSTEM EQUIPMENT – PART 7: HEADPHONES AND EARPHONES from SAI Global. IEC Ed. Sound system equipment – Part 7: Headphones and earphones IEC (E), is applicable to headphones, headsets, earphones.

Author: Dushicage Misar
Country: Trinidad & Tobago
Language: English (Spanish)
Genre: Love
Published (Last): 12 October 2013
Pages: 87
PDF File Size: 6.50 Mb
ePub File Size: 20.92 Mb
ISBN: 701-8-12181-242-1
Downloads: 63193
Price: Free* [*Free Regsitration Required]
Uploader: Voodoonris

There are several unique Signal Paths used in the sequences which are not a part of the default SoundCheck installation. Hardware Requirements In order to run the sequences, the following hardware is required: You are ready to start the sequence.

Five separate sequences are provided, each designed to measure specific characteristics. The spectra are then power summed to derive a single SPL value and the Hz fundamentals are post processed to derive their SPL values.

It then calculates the voltage required to produce 1 mW into the rated impedance. Once calibrated, position the microphones 0. This sequence uses a pink noise stimulus to characterize the passive, active and total attenuation of noise cancelling headphones.

This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3.

A statistics step calculates the mean of the 3 unoccluded measurements. Accept and continue Learn more about the cookies we use and how to change your settings. It then enters a loop which will run 5 times. If passive, connect to the headphone amp or separate audio power amplifier You are ready to start the sequence. The user is first prompted to enter the 77 voltage.

  GUJARATI ENGLISH BARAKHADI PDF

Connect the impedance boxes between the headphone amp out and headphone input. The play and record acquisition takes place 3 times and the user is prompted to reposition the DUT on the HATS in between acquisitions.

Relink dialog Here is a list of sequences and their default signal paths unique paths are in bold: If more than 6068 input channels are available, all input signal paths may be assigned to separate hardware channels. Marking, Microphones, Audio systems, Ratings, Designations, Instructions for use, Headphones, Classification systems, Frequency response, Earphones, Audio equipment, Voltage measurement, Impedance measurement, Testing conditions, Preamplifiers, Comparative tests, Acoustic measurement, Electrical wave measurement, Electrical properties and phenomena, Acoustic testing.

BS EN 60268-7:2011

First, a pink noise stimulus is played from the noise speakers and recorded by the unoccluded ears. It is recommended that the sequences be run directly from the IEC folder.

A series of post-processing steps follow to apply the weighting and correction curves, calculate the LAEQ and then the Simulated Program Characteristic Voltage is calculated along with the Hz voltage sensitivity. Setup System, Hardware and Calibration Before attempting to run any of the sequences, read the following setup instructions.

Crosstalk and radiation curves are then shown on the final display. Iev sequence then goes through a series of acquisition steps to generate four fundamental curves which are then post-processed to calculate crosstalk.

IEC Headphone Test Sequences – Listen, Inc.

No – I don’t want to receive the latest audio test information by email. The sequence prompts the operator to enter the rated voltage and rated impedance ieec the DUT. If the answer is No, the sequence jumps to post-processing steps which calculate passive attenuation and the final display step. Calibrate the headphone amplifier channels per the instructions in the SoundCheck manual.

  ANEES-UL-ARWAH IN ENGLISH PDF

Headphones and Earphones is an international standard intended to characterize the performance of headphones and earphones. The content you have requested is available only to registered visitors. The Hz recorded time waveforms are processed using heterodyne analysis to derive their fundamental values. Learn more about the cookies we use and how to change your settings. Matthew Miller November 15, – 6: Software Requirements SoundCheck Calibrate the microphones per the instructions in the SoundCheck manual.

A pink noise stimulus is played from the noise speakers and recorded by the occluded ears. Sound System Equipment — Part 7: Search all products by.

This approach provides the user with the flexibility to measure all or some of the characteristics of their headphone.

IEC | IEC Webstore

The folder contains dependent files required to run the sequences. Find Similar Items This product falls into the following categories. The sequence uses uec stepped sine stimulus to measure frequency response, THD and impedance, a composite signal of 70 Hz and Hz with an amplitude ratio of 4: